silego technology, inc. rev 1.04 000-00055566-104 revised may 4, 2011 usb host charger identification analog switches SLG55566 SLG55566a block diagram general description the SLG55566/SLG55566a is a usb device that combines high speed usb switches with a usb host charger (dedicated charger) identification circuit. the device supports both the latest usb battery charging specification revision 1.2 in- cluding data contact detection and a set resistor bias for ap- ple compliant devices as well as legacy usb d+/d- short de- tection using data line pull-up. features ? high speed usb switching ? low 4.0pf (typ) on capacitance ? low 4.0 (typ) on resistance ? low 0.5 (typ) on resistance flatness ? 2.8v to 5.5v supply range ? low 8 a (typ) supply current ? automatic current-limit switch control ? automatic usb charger identification circuit ? usb battery charging specificatlon 1.2 compliant ? pb-free / rohs compliant ? halogen-free ? tdfn-8 package pin configuration - SLG55566 pin configuration - SLG55566a vdd gnd tdp tdm cb dp dm cen# 2 3 45 6 7 8 SLG55566 1 thermal pad connected to gnd tdfn-8 (top view) vdd gnd tdp tdm cb dp dm cen 2 3 4 5 6 7 8 SLG55566a 1 thermal pad connected to gnd tdfn-8 (top view) fsm logic one shot + - v ref1 + - v ref1 cen# or cen cb dm dp + - v ref2 fet v dd tdp tdm resistor divider resistor divider
000-00055566-104 page 2 of 9 SLG55566 SLG55566a pin description - SLG55566 pin description - SLG55566a pin # name type description 1 cen# output p-fet open drain output. current limi t switch (cls) control output. cb changes from 0 to 1 or 1 to 0. cen# will be high for 1 second (typ) 2 dm input/output usb connector d- 3 dp input/output usb connector d+ 4 gnd gnd ground 5 vdd pwr power supply. connect a 0.1 f capacitor between vdd and gnd as close as possible to the device. 6 tdp input/output host usb transceiver d+ connection 7 tdm input/output host usb transceiver d- connection 8 cb input switch control bit 0 = autodetection charge r identification active 1 = pass-through mode active, dp/dm connected to tdp/tdm 9 thermal pad gnd ground pin # name type description 1 cen output n-fet open drain output. current limi t switch (cls) control output. cb changes from 0 to 1 or 1 to 0. cen will be low for 1 second (typ) 2 dm input/output usb connector d- 3 dp input/output usb connector d+ 4 gnd gnd ground 5 vdd pwr power supply. connect a 0.1 f capacitor between vdd and gnd as close as possible to the device. 6 tdp input/output host usb transceiver d+ connection 7 tdm input/output host usb transceiver d- connection 8 cb input switch control bit 0 = autodetection charge r identification active 1 = pass-through mode active, dp/dm connected to tdp/tdm 9 thermal pad gnd ground ordering information part number type SLG55566v tdfn-8 SLG55566av tdfn-8 SLG55566vtr tdfn-8 - tape and reel SLG55566avtr tdfn-8 - tape and reel
000-00055566-104 page 3 of 9 SLG55566 SLG55566a absolute maximum conditions parameter min. max. unit supply voltage -0.3 6.0 v continuous current into any terminal -30 +30 ma continuous power dissipation -- 954 mw operating temperature range -40 85 c junction temperature 150 c storage temperature range -65 150 c lead temperature (soldering, 10s) 260 c electrical characteristics - power supply v dd = 2.8v to 5.5v, t a = 25 c (unless specified otherwise) symbol parameter condition/note min. typ. max. unit v dd power supply range v cb > v ih 2.8 -- 5.5 v v cb = 0v 4.75 -- 5.25 v i dd supply current v cb = v dd , v dd = 3.3 -- -- 6 a v cb = v dd , v dd = 5.5 -- -- 8 a v cb = 0v, v dd = 4.75 -- 110 145 a v cb = 0v, v dd = 5.25v -- 120 160 a i dd supply current increase 0 v cb v il or v ih v cb v dd -- -- 2 a electrical characteristics - analog switch v dd = 2.8v to 5.5v, t a = 25 c (unless specified otherwise) symbol parameter condition/note min. typ. max. unit v dp , v dm analog signal range 0 -- v dd v r on on resistance tdp/tdm switch v dp = v dm == -0.4v to 0.4v i = 10ma -- 3.5 -- v dp = v dm = 0v to 3.3v v dd = 5.0v -- 4.0 7 r on on resistance match be - tween channels tdp/tdm switch v dd = 5.0v v dp = v dm = 400mv i dp = i dm = 10ma -- 0.1 -- r flat on resistance flatness tdp/tdm switch v dd = 5.0v v dp = v dm = 0v to v dd i dp = i dm = 10ma -- 0.5 -- r short on resistance of tdp/tdm short v cb = 0v v dp = 1v i dp = i dm = 10ma -- 50 70 i tdpoff , i tdmoff off-leakage current v dd = 3.6v v dp = v dm = 0.3v to 3.3v v tdp = v tdm = 3.3v to 0.3v v cb = 0v -250 -- 250 na i dpon , i dmon off-leakage current v dd = 3.6v v dp = v dm = 3.3v to 0.3v v cb = v dd -250 -- 250 na
000-00055566-104 page 4 of 9 SLG55566 SLG55566a electrical characteristics - dynamic performance v dd = 2.8v to 5.5v, t a = 25 c (unless specified otherwise) symbol parameter condition/note min. typ. max. unit t on turn on time v tdp or v tdm = 1.5v r l = 300 c l = 35pf --? 20 100 s t off turn off time v tdp or v tdm = 1.5v r l = 300 c l = 35pf --? 1 5 s t plh , t phl tdp/tdm switch propaga - tion delay r l = r s = 50 -- 60 -- ps t skew output skew skew between dp and dm when connected to tdp and tdm r l = r s = 50 -- 40 -- ps c off tdp/tdm off-capacitance f = 1mhz --? 2.0 -- pf c on dp/dm on-capacitance f = 240mhz --? 4.0 5.5 pf bw -3db bandwidth r l = r s = 50 -- 950 -- mhz v iso off-isolation v tdp, v dp = 0dbm r l = r s =50 f = 250mhz -- -19.5 -- db v ct crosstalk v tdp, v dp = 0dbm r l = r s = 50 f = 250mhz -- -24.9 -- db electrical characteristics - internal resistors v dd = 2.8v to 5.5v, t a = 25 c (unless specified otherwise) symbol parameter condition/note min. typ. max. unit r pd dp/dm short pull-down 350 500 700 k rt rp rp1/rp2 ratio 1.485 1.5 1.515 ratio r rp rp1 + rp2 resistance 93.75 125.0 156.25 k rt rm rm1/rm2 ratio 0.8544 0.863 0.872 ratio r rm rm1 + rm2 resistance 69.75 93.0 115.18 k electrical characteristics - logic input v dd = 2.8v to 5.5v, t a = 25 c (unless specified otherwise) symbol parameter condition/note min. typ. max. unit v ih cb input logic high 1.4 -- -- v v il cb input logic low -- -- 0.4 v i in cb input leakage current v dd = 5.5v 0 v cb v il or v ih v cb v dd -1 -- 1 a
000-00055566-104 page 5 of 9 SLG55566 SLG55566a electrical characteristics - cen#/cen outputs v dd = 2.8v to 5.5v, t a = 25 c (unless specified otherwise) symbol parameter condition/note min. typ. max. unit t vbt v bus toggle time cb = logic 0 to logic 1 or logic 1 to logic 0 0.5 1 1.5 s v oh_cen# cen# output logic high voltage cb = logic 0 to logic 1 i sink = 2ma v dd -0.4v -- -- v i out_cen# cen# output leakage cur - rent v dd = 5.5v v cen# = 0v or cen# deasserted -- -- 1 a v ol_cen cen output logic low volt - age cb = logic 0 to logic 1 i source = 2ma -- -- 0.4v v i out_cen cen output leakage cur - rent v dd = 5.5v v cen = 5.5v or cen deasserted -- -- 1 a electrical characteristics - esd protection v dd = 2.8v to 5.5v, t a = 25 c (unless specified otherwise) symbol parameter condition/note min. typ. max. unit v esd esd protection level (dp and dm only) human body model -- 8 -- kv v esd esd protection level (all other pins) human body model -- 2 -- kv
000-00055566-104 page 6 of 9 SLG55566 SLG55566a package top marking system definition part id assembly code datecode lot revision 8 7 6 5 1 2 3 4 ? part id field: identifies the specific device configuration ? assembly code field: assembly location of the device. ? date code field: coded date of manufacture ? lot code: designates lot # ? revision code: device revision xx a dd l r
000-00055566-104 page 7 of 9 SLG55566 SLG55566a package drawing and dimensions 8 lead tdfn package d e a b c 0.15 c 0.15 a1 a3 a2 a detail a b c 0.10 a b m c 0.05 m detail b symbol min (mm) nom (mm) max (mm) 0.70 0.75 0.80 a 0.00 -- 0.05 a1 -- 0.55 -- a2 -- 0.20 -- a3 0.20 0.25 0.30 b 1.90 2.00 2.10 d 1.50 1.60 1.70 d2 1.90 2.00 2.10 e 0.80 0.90 1.00 e2 0.50 bsc e 0.20 0.30 0.40 l seating plane detail a c 0.10 c 0.08 c d2 pin 1 0.25x45 l detail b e2 e
000-00055566-104 page 8 of 9 SLG55566 SLG55566a tape and reel specifications tape and reel drawing package type # of pins nominal package size units per reel trailer a leader b pocket tape (mm) reel diameter (mm) pockets length (mm) pockets length (mm) width pitch 8tdfn 8 2x2mm 3,000 42 168 42 168 8 4 178 f (iii) w e1 1.75 0.1 p0 4.00 0.1 (ii) a0 p1 p2 2.00 0.05 (i) d0 ? 1.55 0.05 d1 ? 1.00 min y y (i) measured from centerline of sprocket hole (ii) cumulative tolerance of 10 sprocket holes is 0.20 (iii) measured from centerline of sprocket hole to centerline of pocket (iv) other material available all dimensions in millimeters unless otherwise stated 2.25 0.1 a0 2.25 0.1 b0 1.00 0.1 k0 3.50 0.1 f 4.00 0.1 p1 8.00 0.1 w (mm) symbol t 0.30 0.05 b0 k0 c l crossection y-y
000-00055566-104 page 9 of 9 SLG55566 SLG55566a silego website & support silego technology website silego technology provides online support via our website at http://www.silego.com/ .this website is used as a means to make files and information easily available to customers. for more information regarding silego green products, please visit: http://greenpak.silego.com/ http://greensak.silego.com/ http://greenlib.silego.com/ http://greenfet.silego.com/ http://greenclk.silego.com/ http://greenddr3.silego.com/ products are also available for purchase directly from silego at the silego online store at http://store.silego.com/ . silego technical support datasheets and errata, application notes and example designs, user guides, and hardware support documents and the latest software releases are available at the sil ego website or can be r equested directly at info@silego.com . for specific greenpak design or applications ques tions and support please send email requests to greenpak@silego.com users of silego products can receive assistance through several channels: online live support silego technology has live video technical assistance and sales support available at http://www.silego.com/ . please ask our live web receptionist to schedule a 1 on 1 traini ng session with one of our application engineers. contact your local sales representative customers can contact their local sales re presentative or field application engineer (fae) for support. local sales offices are also available to help customers. more information regarding your lo cal representative is available at the silego website or send a request to info@silego.com contact silego directly silego can be contacted directly via e-mail at info@silego.com or user submission form, located at the following url: http://support.silego.com/ other information the latest silego technology press releases, listing of seminars and events, listings of world wide silego technology offices a nd representatives are all available at http://www.silego.com/ this product has been designed and qualified for the consumer market. applications or uses as critical components in life support devices or systems are not author ized. silego technology does not assume any liability arising out of such appli - cations or uses of its products. silego technology reserves the right to im prove product design, f unctions and reliability without notice .
|
